The Random Thoughts of a Geek heading for Banbury
The Random Thoughts of a Geek heading for Banbury

I Have Made a Cool Thing, Now I want to sell it!

In the UK if you want to place some thing on the market you need to ensure that it has a CE mark and has a DoC (Declaration of Conformity), there are a number of things that need to be done. Looking through the list, we have CE1, RoHS2, WEEE3, and LVD4.

So what do these mean as someone who has just made an awesome electrical device?

If you need EMC work done on your product you should talk to Jason at CASS Industries, who will be able to help you!

RoHS 2

Restriction of Hazardous Substances – Directive 2011/65/EU (repeals RoHS 1 2002/95/EC and 2008/35/EC) can be done as a paperwork test, Farnell and other suppliers offer to let you search only by RoHS compliant components, so use only these, Lead free PCBs, and lead free solder, and unless you do something daft you won’t go wrong.

It is ok to use Lead solder and HASL PCBs for prototyping, but for production you must work under RoHS 2.

WEEE

Waste Electrical and Electronic Equipment Directive – 2012/19/EU (repeals 2002/95/EC) it sets out that “Users of electrical and electronic equipment from private households should have the possibility of returning WEEE at least free of charge”, the easiest way to implement compliance is to write in the attached documentation something like “The device shall be returned to you for disposal” (and you will cover the P&P of this!) however it is unlikely that you will ever get any returns, however that is not your issue… You can then place the logo with the black line on your instructions or rating plate (WEEE logo for items placed on the market between 2002 and 2005 has no black bar, after 2005 does).

LVD

Low Voltage Directive – 2014 /35/EU (replaced 2006/95/EC in April 2016). In the United Kingdom, the LV directive is implemented by “The Electrical Equipment (Safety) Regulations 1994” (a read of BS EN 60335-1:2012 will give you most of what you need to know) however! Battery power is your friend (A supply voltage of above 75 V dc or 50 V ac requires LVD).

Or buy pre certified wall warts, and when I say pre certified I don’t just mean from China, unless you can tell me what is wrong with this certificate:

Go on, tell me, as this is typical of a certificate you will get for anything bought from China, tell me why it is not valid for a wall wart (hint it is not for a wall wart).

I talked about parts of an LVD on one of my other sites for a Hi-Link HLK PM01(second assessment), at some point I will do a full assessment on an £0.89p Phone charger.

CE for EMC

CE marking is a mandatory conformity marking for certain products sold within the European Economic Area (EEA) since 1985. There are a large number of other mandatory conformity markings for other market areas, FCC for the USA (Note that the FCC mark bears no legal status where the CE mark does, and vice versa).

The EMC (Electromagnetic Compatibility Regulations) regulations are intended to allow electronic devices to operate in the same vicinity without causing interference to one another.

An excerpt below from the Electromagnetic Compatibility Regulations 2006, Regulation 4 paragraph 2 states:

Equipment shall be designed and manufactured, having regard to the state of the art, so as to ensure that the electromagnetic disturbance it generates does not exceed a level above which radio and telecommunications equipment or other equipment cannot operate as intended; and it has a level of immunity to the electromagnetic disturbance to be expected in its intended use which allows it to operate without unacceptable degradation of its intended use.

There are fundamentally two parts to electromagnetic compatibility.

  1. The electromagnetic disturbance, or emissions generated by a piece of equipment.
  2. The ability of a piece of equipment to withstand electromagnetic noise whilst still functioning as intended.

Any piece of equipment, or product, that is “placed upon the market” must meet the basic tenets of the EMC regulations.

A product, failing to meet the EMC requirements would not only be a breach of the regulations, but could conceivably place both the operator and the general public at risk.

The EMC Directive (2004/108/EC) essentially states that before any product is sold in the EU, the supplier (who may be the manufacturer or the importer) must ensure that it will not cause interference (emissions), and that it will operate satisfactorily in its intended environment (immunity).

Test techniques to check the various aspects of emissions and immunity are specified in the EMC Standards. These are the compliance tests. These standards include details of the maximum allowable levels of emissions, and the immunity ‘stress’ levels that must be applied.

Electromagnetic emissions produced by a product above prescribed limits could interfere with any of the following items:

  • Radio and television receivers
  • Information technology networks (eg. WiFi, Internet connections)
  • Home automation systems
  • Computer based equipment
  • Emergency call systems
  • Medical equipment
  • Emergency services and enforcement agency communications

The list is representative only. It is not exhaustive and could include many other items.

Inadequate electromagnetic immunity of a product could cause the product to malfunction. The severity of the consequences of failure will vary, depending upon product type and purpose. In the most serious cases, equipment malfunction could cause physical injury, loss of limbs, lacerations, blindness, burns, poisoning, suffocation, or cardiac arrest. In addition, equipment malfunction could cause damage to property.

If you can argue that it’s attended equipment. Non medical. Non critical and won’t have any degradation of performance under the immunity requirements of BS EN 61000-6-1 you should be fine…

As such you should still look at having emissions testing done, you can sidestep the requirement for Conducted emissions if you don’t use mains power, and don’t even offer rechargeable batteries via a USB connection.

Which leaves us with the one and only test you should perform. BS EN 61000-6-3 table 1 (numbers are the same for FCC cei 61000-6-3 and Iec 61000-6-3)

I have tested two servos for ERAD here (ECON here), so you can get an idea of some of the setup requirements.

And before you say to yourself that how can you design something that doesn’t work, tell me what the difference is between these two graphs, other than one is a pass, and the other is a fail:

The difference is a 100 nF cap between Vcc and GND on the Pic μC

LiPol Batteries

Please don’t use LiPol batteries and think that you know how to roll your own charger, it will end in tears:

Method of Charging

Set an output voltage of 4.2V on a voltage supply and adjust the current limit to 1.5A maximum output current.

Taking care to observe the correct polarity, apply the supply voltage to the battery and monitor the current.

At first, the supply will operate in “constant current mode”, drawing the maximum available current from the supply. The voltage will initially read lower than the original voltage setting, but will rise over time as the battery charges.

A point will be reached in the charging cycle where the battery voltage reaches the charging set voltage of the power supply. At this point, the charging current will start to fall and the battery voltage will remain constant. This charging mode is referred to as “constant voltage mode”.

Once constant voltage mode has been achieved, the current decay is closely monitored. When the current falls to a chosen value, typically between 0.02C and 0.1C, then the battery is deemed to be fully charged and the supply voltage must be removed.

If the battery has not achieved a fully charged condition after three hours of continuous charging, then the charge cycle should be terminated and the voltage supply removed.
Warnings

The voltage applied to a Lithium cell must never exceed the absolute maximum of 4.25V at any time.

A lithium cell should not be allowed to continuously charge, or trickle charge as this is detrimental to the cell chemistry. Once full charge has been achieved, the applied charging voltage should be completely disconnected in order to remove the voltage stress placed upon the cells.

Lithium cells should never be discharged below 2.7V and should contain protective circuits to prevent that condition.

Charging lithium cells at a value of current greater than 1C is not generally recommended, although some chemical variants are more tolerant than others.

The charging circuit should not re-engage before the overall cell charge has dropped by at least 5% to10% from maximum. This would be manifested as a drop in voltage from the absolute maximum of 4.25V to around 4.0V to 4.1V.

RED

Oh and if you use a radio module I will find new and unhappy ways to cry as that 1. Brings in the RED (Radio Equipment Directive) and LVD again. But if you must use a radio module, and want to avoid a week’s worth of testing buy a pre-approved module!

Paper work

All of these tests bring in paperwork requirements,

Labelling

  • A product label showing a Manufacturer’s name / trade mark AND address is required.
  • A product label showing an Importers name / trade mark and address is required.
  • A product label showing a type, batch or serial number is required, this should also appear on the DoC (Declaration of Conformity) to aid traceability.
  • An importer or distributor is considered to be a manufacturer if he places the equipment on the market in his own name or modifies the equipment in such a way that compliance with the Directive may be affected.

Documentation

Instructions for Use must be provided with the equipment.

Technical Documentation must be held (and be available for examination) by the manufacturer, an authorised representative or an importer, to include:

  • A general description of the apparatus.
  • Conceptual design and manufacturing drawings and schematics of components, sub-assemblies, circuits, etc.
  • A list of the harmonised standards applied in full or in part the references of which have been published in the Official Journal of the European Union, and, where those harmonised standards have not been applied, descriptions of the solutions adopted to meet the essential requirements of the Directive. In the event of partly applied harmonised standards, the technical documentation shall specify the parts which have been applied.
  • Results of design calculations made, examinations carried out, etc.
  • Test Reports.
  • The electromagnetic compatibility assessment.

A DoC (Declaration of Conformity) must be raised by the manufacturer or an Authorised Representative (who has a formal written mandate from the manufacturer to do so).

The DoC must include information to allow easy identification of the product (batch number or photograph etc.)

The DoC must be kept 10 years from the date of placing the item on the market.

Compliance to more than 1 Directive should be shown on a single DoC with references to the appropriate Directives and Standards, however a DoC should not be made to more than one Directive if they cover the same areas (e.g. EMC and RED or LVD and RED).

Sample DoC

Sample DoC
Sample DoC
  1. CE marking is a mandatory conformity marking for certain products sold within the European Economic Area (EEA) since 1985. The CE marking is also found on products sold outside the EEA that are manufactured in, or designed to be sold in, the EEA.
  2. RoHS is a set of EU regulations that implements EU Directive 2002/95 that restricts the use of hazardous substances in electrical and electronic equipment. This directive bans placing on the EU market, any product having an electrical/electronic component containing more than thresholds set for lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) flame retardants.
  3. The Waste Electrical and Electronic Equipment Directive (WEEE Directive) is the European Community directive 2012/19/EU on waste electrical and electronic equipment which, together with the RoHS Directive 2002/95/EC, became European Law in February 2003.
  4. Low Voltage Directive

Leave a comment

Your email address will not be published. Required fields are marked *

4 thoughts on “I Have Made a Cool Thing, Now I want to sell it!”